Search found 182 matches

by Beano
Sat Apr 23, 2022 10:27 am
Forum: General Discussion
Topic: Slicers
Replies: 18
Views: 2879

Re: Slicers

Cheers Guys, yes, I am already using similar type of settings, I was just hoping someone had a complete profile that would address support structures, bridge flows, etc...

If not, I will tune mine then and share later.
by Beano
Fri Apr 22, 2022 3:17 am
Forum: Control Board & Firmware
Topic: Firmware Configuration - Duet
Replies: 11
Views: 3475

Re: Firmware Configuration - Duet

Hi, Mmm...I replied before I saw you had this fixed, anyway, below methodology works well: M669 K1 ; select CoreXY mode ; Drives M569 P0.0 S1 ; physical drive 0.0 goes forwards - X-Axis M569 P0.1 S1 ; physical drive 0.1 goes forwards - Y-Axis M569 P0.2 S1 ; physical drive 0.2 goes forwards - Extrude...
by Beano
Fri Apr 22, 2022 2:37 am
Forum: General Discussion
Topic: Slicers
Replies: 18
Views: 2879

Re: Slicers

Hello Teeminus, Guys,
Can you perhaps share your Prusa or Super Slicer, or Cura, profile/config for your hevort, for either PLA or PLA+? Would give me a good starting spot, will be appreciated ;)

Cheers,
Beano
by Beano
Thu Apr 21, 2022 7:24 am
Forum: The Show Room
Topic: Nemesis - my buildlog
Replies: 158
Views: 17546

Re: Nemesis - my buildlog

Cheers Glenn, will post a few pix on the weekend! Need to fine-tune my slicer, but prints are looking great!
by Beano
Thu Apr 21, 2022 6:50 am
Forum: The Show Room
Topic: Nemesis - my buildlog
Replies: 158
Views: 17546

Re: Nemesis - my buildlog

Ha, finally getting back to Nemesis.

Busy designing a 4-axis active belt tensioner for my racing sim, and now in need of printing some custom pieces. Just doing the first run of a belt roller, will post pix over the weekend. It lives, hehe.
by Beano
Tue Sep 28, 2021 9:37 pm
Forum: The Show Room
Topic: Glenn's HevORT, size TBC HD9 build!!
Replies: 5
Views: 942

Re: Glenn's HevORT, size TBC HD9 build!!

He, great to see your progress, Glenn, and yes, HD9 a bloody awesome choice! Probably the best option, if staying with steppers, tbh. Looking forward to more! Glad you made it over from the Dark Side :)
by Beano
Wed Sep 22, 2021 8:18 am
Forum: The Show Room
Topic: Nemesis - my buildlog
Replies: 158
Views: 17546

Re: Nemesis - my buildlog

Ha, fine-tuning this beast's gunna be fun, Glenn! Just busy making adjustments to the belts, playing more than doing anything useful actually :) Will start serious tuning on the weekend, then will dump some nylon-cf filament in and print the housing for my iRacing Porsche 919 LMP1 steering-wheel. Ho...
by Beano
Wed Sep 22, 2021 7:22 am
Forum: The Show Room
Topic: Nemesis - my buildlog
Replies: 158
Views: 17546

Re: Nemesis - my buildlog

Busy calibrating my Hevort now, printing some cube to check ringing, getting better. Then will tune the harmonics quickly using the accelerometer on the Duet Toolboard, do the spectrum analysis quickly, and enter the resonant frequency in the config file, then will print something to see how it does...
by Beano
Fri Sep 17, 2021 6:09 pm
Forum: The Show Room
Topic: My 515x515x540 HD12 Build
Replies: 286
Views: 38954

Re: My 515x515x540 HD12 Build

Great news! And lols at your last statement, reminds me recently dumping the HextrudORT because I kept having stepping issues, using a variety of steppers and hot-ends….and the culprit turned out to be clogging the heat-break because the fan used for cooling was to small. Shipped with the Mosquito, ...
by Beano
Thu Sep 16, 2021 7:21 am
Forum: The Show Room
Topic: Nemesis - my buildlog
Replies: 158
Views: 17546

Re: Nemesis - my buildlog

With the Duet web-interface, and since RRF FW V3.2, there is support for accelerometers. This can of course be used to calibrate your device to remove harmonics at specific frequencies. Lucky me, the Duet Toolboard I am using on my print-head has a built-in accelerometer, I had to add a quick gcode ...